Electrical Adjustments Test Mode 2 A board. Anode button 1 Turn up one side of the rubber cap in 2 Using a thumb pull up the rubber cap 3 When one side of the rubber cap is the direction indicated by the arrow a firmly in the direction indicated by the separated from the anode button, the arrow b anode-cap can be removed by turning 3 C board up the rubber cap and pulling it up in the direction of the arrow c.
A metal fitting called as shatter-hook terminal is built into the rubber. This is performed by cutting the gates with a sharp wire cutter at the locations The plates are identified by markings A-B-C-D-E on their top side. Identify the plate by locating its marking. Note : There are 5 plates fitted to the main bracket and secured by 4 or 6 gates. Turn the plate over noting where the marking is located. Only remove the necessary plate to gain access to the circuit board.
Locate the corresponding marking indicated on the main chassis bracket. See Fig 2. Refit the plate as indicated in Fig 3 with the markings located next to each other. Beam landing adjustments. Focus carry out these adjustments with the rated power 4. White balance supply. Degausser Contrast DC power supply normal 4. Digital multimeter Brightness Preparation: Fig. Input the white signal with the pattern generator.
Set the pattern generator raster signal to red. Move the deflection yoke forward and adjust with the Green purity control so that the red is at the centre and the blue and the green take up equally sized areas on Fig. See Fig. Move the deflection yoke forward and adjust so that Blue the entire screen becomes red.
Switch the raster signal to blue, then to green and verify the condition. Disk magnets or 6. When the position of the deflection yoke has been rotatable disk decided, fasten the deflection yoke with the screws. Purity control corrects magnets correct 7. If the beam does not land correctly in all the corners, this area. Deflection yoke positioning corrects these areas. STAT magnet. Center dot R G 4. If the V. STAT magnet is moved in the direction of B the a and b arrows, the red, green, and blue points move as shown below.
Moving horizontally , adjust the H. STAT control so b that the red, green, and blue points are on top of b. Moving vertically , adjust the V. STAT magnet so that the red, green, and blue points are on top of each other at the centre of the screen. If the H. STAT variable resistor cannot bring the red, green, and blue points together at the centre of the screen, adjust the horizontal convergence with the a b H. STAT variable resistor and the V.
STAT magnet in 3 b the manner given below. Use the H. STAT VR to adjust the red, green, and blue dots so they coincide at the centre of the screen by moving the dots in the horizontal direction. Preparation: 2. Remove the deflection yoke spacer. Move the deflection yoke as shown in the figure static convergence and the vertical static convergence. Slightly loosen the deflection yoke screws. Tighten the deflection yoke screws.
Re-install the deflection yoke spacer. Switch the set into AV mode apply no signal to the AV connectors. Adjust RV01 to obtain a voltage of 3. Input an all white signal from the pattern generator. Enter into the service mode. Enter into Picture Adjustment service menu. Select sub-contrast and adjust to 7.
Select the Green Drive and adjust so that the white balance becomes optimum. Select the Blue Drive and adjust so that the white balance becomes optimum. Press the TV button to return to TV operation. Fitness, Sports, Golf. Home GPS Accessories. Sort By:. Displaying 1 - 48 of results. Garmin 20' Marine Network Cable. In Stock. Add To Cart. Global shipping constraints and other material shortages have slowed the supply of products in many industries, including GPS and Marine electronics.
We update the Estimated Shipping Date on our website in real time, so feel free to check back frequently. Garmin Motorcycle Mount Bracket. Garmin Carrying Case. Garmin 6' Marine Network Cable. Garmin Quick Release Lanyard.
Garmin Li-ion Battery pack for Rino and Series. Garmin tempe External Temperature Sensor. Garmin Carabiner Clip for Handhelds. Garmin Bicycle Mount for Montana Series. Garmin Marine Mount. Garmin Handlebar and Cart Mount. Garmin portable friction mount for Nuvi.
Garmin Constant Power Cable. Garmin MapSource Topo U. The control panel of the failed fan will be grey out, so you can quickly identify which fan is causing issues. Immediately personalize your lighting with the recommended color palette. You can change colors and brigthness for the LED ring which featrues You also can let each LED display a specific color. Users are allowed to choose the way they want to display graphics card or install the power supply vertically for ultimate system display.
Entailed with up to 11 drive locations for 3. Comes with cooling fitment for CPU coolers up to mm in height. Houses PSU sizes up to mm in length. Constructed with individual chambers and aluminum mesh panels design, along with 3 preinstalled mm Riing Plus LED RGB fans, Level 20 ensures the heat produced by each main heat source is efficiently dissipates, modulate the airflow to perfection. USB 3.
Toggle navigation. Individual Aerodynamic Chamber Design Level 20 utilizes trio chamber design to achieve ventilation and space management optimization. Motherboard Chamber Supports both vertical and horizontal power supply orientations, allowing versatile placement options. Power Supply Chamber Supports both vertical and horizontal power supply orientations, allowing versatile placement options.
Aluminum Modular Structural Statement with 4mm Thick Tempered Glass Features aluminum panels of which the aluminum anodizing process establishes water and corrosion resistant performance.
0コメント